Sunday, February 27, 2022
Gangway
I finished the first half of the gangway frame this weekend. We still need to re-stain the deck boards and attach them, but I don't want to do that until we have it assembled and on the dock. I also need to fabricate the mounts that will hold it on the dock and the retaining wall. I'll do that after I finish the second half.
Tuesday, January 18, 2022
Gangway
I now have the mounting hardware all done for the side rails on the gangway. There are brackets that clamp over the top and under the bottom of the sides and bolts that go through the top and bottom rail to hold the 2 halves together. Where the bolts run through, I drilled and welded in aluminum tube, so the bolts don't crush the side rails. Next up is to make the deck and bracing on the under side.
Monday, January 10, 2022
Gangway
About a year after we bought the cabin, we picked up a 20' long wood gangway. It worked well, but it was really heavy and very difficult to get in and out of the water. We've wanted one that was lighter and easier to handle for quite a while now. I finally decided, this is the year I will build one out of aluminum. I've built the 4 side rails already. These will bolt together to make a pair of 20' long girders.
Saturday, December 18, 2021
Boat Lift
The pump box for the new boat lift is all ready to go when the weather gets better. I put a new motor on the pump, cleaned all the old oil out of the pump and reservoir and scraped all the old oil (which looked more like caramel) out of the bottom of the box. I put a new solar charge controller on the lid of the box, so I just need some fittings, a battery and some new cables when we put it in the water this spring.
Friday, December 17, 2021
Retaining Wall
While I was at the lake today, I noticed our neighbor's retaining wall on the beach had collapsed. While inspecting the damage, I found that ours had also taken quite a bit of damage also. So I guess we get to rebuild these walls this summer sometime. Why not, we've had to build or re-build every other retaining wall on the property. I guess now we can expand our lawn and eliminate the seam between the walls.
Sink Base Doors
I had to be at the cabin most of the day today for a drywall inspection. While I was there, I cut the holes and mounted the doors on the front of the sink base. You can just see where I had to trim about 1/2" off the top of the doors so they clear the bottom of the sink. I still need to sand and paint that area. I also plan to make a set of small trim pieces that fits next to the sink on either side to finish it off.
Sunday, November 28, 2021
Water Softener
In order to hook up the water softener, I needed to install a floor drain in the back of the girls closet. That drain is installed and hooked up to the utility room sink drain under the house. The only thing left to install the water softener is to setup the discharge lines to dump water into this drain. The hardware store didn't have the fittings I needed, so I will do that the next time I go up there.
Saturday, November 27, 2021
Water Heater
The water heater is finished and ready to turn back on this spring. Before hooking up the vent, I had to build a shelf to put in the corner. Before the tree came down, Tlo managed to get stuck behind the water heater and we had to lower Kylee down by her ankles in order to grab him. I also had to cut an attic access in the closet in order to hook up the vent pipe in the ceiling. I still need to trim out that access hole.
Friday, November 26, 2021
Boat Lift
Over the summer we picked up a 2 ton hydraulic boat lift for cheap. It sat in the muck for a while and worked itself out of level. So when the previous owner lowered the lift, the bottom rails bent. I have the new sections built and attached. All that is left on these 2 pieces is the drill the 3/4" holes for the deep water side pivots. I'm also in the process of rebuilding the hydraulic cylinder.
Tuesday, November 16, 2021
Mechanical Closet
I spent some time working on the mechanical closet this weekend. The water heater is installed as far as the pan, supply and outlet lines. I still need to do the over pressure drain and the exhaust vent. The radiant floor heat manifold is also attached to the wall and the trim has been built around the tubes. The water softener is nearly ready to go in as well. All that is left there is a drain in the floor.
Subscribe to:
Posts (Atom)